🚥Operation
      Back to home
      1. Help Center
      2. Light Storm 1200d Pro
      3. 🚥Operation

      [LS 1200d Pro] Getting Started

      Setting up and powering the LS 1200d Pro

      Attaching/Detaching the Protection Cover

      Press the release button following the arrow and rotate the cover clockwise to detach the cover. To reattach the cover, insert it into the Bowens mount and rotate counter clockwise.

      Screen Shot 2023-07-11 at 4.29.05 PM

      Notice: Always remove the protection cover prior to turning on the light. Always re-install the cover when packing it away.

      Attaching/Detaching the Bowens Mount Hyper Reflector (LS 1200 Series)

      To install the reflector, press the release button, insert the reflector into the Bowens mount, and rotate it counter clockwise as shown in the following pictures. To remove the reflector, pull back the release button and rotate the reflector clockwise.

      Screen Shot 2023-07-11 at 4.29.15 PM

      Mounting the Lamp Head

      • Baby Pin (Pin ⌀ = 5/8 in, 16 mm): loosen stand mounting screw / tie-down, mount on stand baby pin, adjust position, tighten T-handle baby pin mounting screw
      • Junior Pin (Pin ⌀ = 1 1/8 in, 28 mm): remove stand mounting screw / tie-down, mount into the stand receiving hole, adjust position, tighten the stand's tie down knob to lock it
      • Adjust the lamp head tilt angle by loosening the tilt lock handle (counter-clockwise rotation) beside the lamp head, then tighten the tilt lock handle to lock the tilt angle (clockwise rotation)

      Screen Shot 2023-07-11 at 4.29.30 PM

      Quick-Release Lightning Clamp Operation Instructions

      1) Clamp the Lightning Clamp onto a light stand or yoke.
      2) To attach the control box, rotate the release lever to unlock the quick-release baseplate, then mount the control box onto the Lightning Clamp (the release lever will automatically spring back).
      3) To remove the control box, grasp it firmly, then unlock the quick-release plate by turning the release lever, and detach the control box.

      Screen Shot 2023-07-11 at 4.29.41 PM

      Quick-Release Lightning Clamp Specifications:

      Weight 670g / 1.48lbs Sizes(L*W*H) 10.35x8.74x12.5cm / 4.07x3.44x4.92in
      The Lightning Clamp can clamp onto square or round pipe with a diameter between 2-5cm or 0.79-1.97in.

       

      Connect the Lamp Head to the Control Box

      Connect the Lamp Head to the Control Cox using the LS 1200 Series 7-Pin Weatherproof Head Cable.

      ls_1200d_pro_connect_the_lamp_head_to_the_control_boxYou can use the Cable relief hook
      to manage the connection line.

      Disconnect the Head Cable by pulling up on the collar of the connector. This will disengage its locking structure. Do not pull directly.

      Powering by AC

      1. ls_1200d_pro_powering_up_by_acSpring Lock
      2. Lock Slot

      To disconnect the Neutrik® powerCon cable, pull back on the yellow release tab on the cable connector, and rotate the connector counter clockwise. Do not pull directly.

      Powering by DC

      Single-way DC power supply 720W 48V supports half power output, dual-way DC power supply 720W 48V supports full power output. If the A/B two-way power supply is not balanced, please promptly turn down the brightness of the lamp head, such as not turn down the brightness, in order to avoid damage, the control box will pop up to remind the interface and suspend the output of the lamp head after the 30-second countdown. (If you need to meet 100% output, please use 48V constant voltage DC power supply)

      Screen Shot 2023-07-11 at 4.30.47 PM

      Press the Power Button to Turn the Light On and Off

      ls_1200d_pro_power_on_off