- Help Center
- Electro Storm Motorized Yoke
- 🦺Safety & Certifications
-
General Help
-
STORM 80c
-
STORM 1000c
-
STORM 1200x
-
Electro Storm CS15
-
Electro Storm XT26
-
INFINIBAR
-
MT Pro
-
MC Pro
-
Nova P300c & P600c
-
Sidus One
-
Sidus Four
-
Light Storm 600c Pro
-
Light Storm 600c Pro II
-
Light Storm 1200d Pro
-
Light Storm 600x Pro
-
Light Storm 600d Pro
-
Light Storm 600d
-
Light Storm 300x
-
Light Storm 300d II
-
Light Storm 60x
-
Light Storm 60d
-
Accent B7c
-
MC
-
Sidus Link Bridge
-
amaran Flexible Lights
-
amaran Pixel Tubes
-
amaran T2c & T4c
-
amaran P60c & P60x
-
amaran 150c & 300c
-
amaran COB 60d S
-
amaran COB 60x S
-
amaran 100d S & 200d S
-
amaran 100x S & 200x S
-
amaran SM5c
-
Modifiers & Accessories
-
Electro Storm Motorized F14 Fresnel
-
Electro Storm Motorized Yoke
-
Spotlight Max
-
amaran Ace 25c
-
amaran Ace 25x
[Motorized Yoke] Safety
Safety Instructions of Motorized Yoke
When using this product, basic safety precautions should always be followed, including:
- Read and understand all instruction before using the fixture.
- Close supervision is necessary when any fixture is used by or near children. Do not leave the fixture unattended while in use.
- Care must be taken as burns can occur from touching hot surfaces.
- Do not operate the fixture if any cord is damaged, or if the fixture has been dropped or damaged, until it has been examined by qualified service personnel.
- Position any power cables such that they will not be tripped over, pulled, or put into contact with hot surfaces.
- If an extension cord is necessary, a cord with an amperage rating at least equal to that required by the fixture should used. Cords rated for less amperage will overheat.
- Always unplug the lighting fixture from the electrical outlet before cleaning and servicing or when not in use. Never yank the cord to remove the plug from the outlet.
- Let the lighting fixture cool completely before storing. Unplug the cables from the lighting fixture and store them in assigned spaces of the carrying case (if being used).
- Do not immerse this fixture in water or any other liquid to avoid electric shock.
- Do not disassemble the fixture to avoid the risk of fire or electric shock. Contact cs@aputure.com or take the lighting fixture to qualified service personnel when service or repair is required. Incorrect reassembly may cause electric shock when the lighting fixture is in use.
- Using any accessory attachment not recommended by the manufacturer may increase the risk of fire, electric shock or injury to any persons operating the fixture.
- Power this fixture by connecting it to a grounded outlet.
- Remove the Protective Cover before use.
- Do not block the ventilation openings or look at the LED light souce directly when it is powered on. Do not touch the LED light source in any condition.
- Do not place the product near combustible and volatile solvents to avoid product damage.
- Use a soft and dry cloth to clean the device
- Ensure all the ports and plugs are complete dry when using the fixture in wet environments to avoid short circuit or electric shock.
- Service and maintenance should only be carried out by authorized service personnel. Any malfunctions caused by unauthorized disassembly are not covered by the warranty. The user may pay for service and maintenance.
- When hanging the fixture overhead, always ensure an extra safety measure has been attached - such as safety chains - that is certified for the weight of the fixture. We recommend only using the original Aputure cable accessories. Please note that any malfunctions caused by using unauthorized accessories are not covered by the warranty. The user may pay for service and maintenance.
- This product is certified by RoHS, CE, KC, PSE, and FCC. Please operate the product in full compliance with relevant country's standards. Any malfunctions caused by incorrect use are not covered by the warranty. The user may pay for service and maintenance.
- The User's Manual was formulated based on rigorous tests performed by the company. No further notice will be given in the event of any change in its design and specifications.